 |
|
   |
General
IC-F3023T/S |
IC-F4023T/S |
|||
|---|---|---|---|---|
| Frequency coverage (Varies according to version) |
136–174 MHz |
400–470 MHz 450–512 MHz (USA) 450–520 MHz (GEN) |
||
| Number of channels | 128 ch/8 zones |
|||
| Channel spacing (Varies according to version) |
12.5/25, 15/30 kHz |
12.5/25 kHz |
||
| Type of emission | 16K0F3E, 11K0F3E |
|||
| Current drain | Tx High | 1.5A |
||
| Rx | Stand-by | 75mA |
||
| Max. audio | 250mA |
|||
| Dimensions (projections not included; W×H×D) |
53×120×36.9 mm 2 3 ⁄32× 4 23/32×1 7 ⁄16 in |
|||
| Weight (approx.) | 300g; 10.6oz (with BP-232N) |
|||
Transmitter
IC-F3023T/S |
IC-F4023T/S |
|
|---|---|---|
| RF output power | 5W |
4W |
| Spurious emissions | 80dB (typ.) |
|
| Frequency stability | ±2.5ppm |
|
| Audio harmonic distortion | 3% typical 40% deviation |
|
| FM Hum and Noise | 46dB typ. (W) 40dB typ. (N) |
|
Receiver
IC-F3023T/S |
IC-F4023T/S |
|
|---|---|---|
| Sensitivity at 12dB SINAD | 0.25μV (typ.) |
|
| Adjacent channel selectivity (W/N) | 70/65dB (typ.) |
|
| Spurious response rejection | 70dB (min.) |
|
| Intermodulation rejection | 75dB (typ.) |
74dB(typ.) |
| AF output power (at 5% distortion with an 8Ω load) |
500mW (typ.) |
|
FUNCTION COMPARISON AND INTERNAL UNIT OPTIONS
IC-F3023T/S IC-F4023T/S |
||
|---|---|---|
| Number of option slots | 1 |
|
| CTCSS/ DTCS | encoder | Available |
| decoder | Available |
|
| 2-Tone | encoder | Available |
| decoder | Available |
|
| 5-Tone | encoder | Available |
| decoder | Available |
|
| DTMF autodial | Available |
|
| DTMF decoder | UT-108R |
|
| Voice Scrambler | Inversion | - |
| Non-rolling | UT-109R |
|
| Rolling | UT-110R |
|
| APCO P25 digital | - |
|
| AES encryption | - |
|
| DES encryption | - |
|
| 6.25kHz digital | - |
|
| MPT 1327 | - |
|
| MDC 1200 | Available (Limited functions) |
|
| LTR™ trunking | - |
|
| PassPort | - |
|
| Man Down function | UT-124R |
|
| Intrinsically safe | - |
|
Applicable U.S. Military Specifications
Icom makes rugged products that have been tested to and passed the following MIL-STD requirements and strict environmental standards.
| Standard | MIL-810 F Method, Proc. |
|---|---|
| Low Pressure Storage | 500.4 I |
| Low Pressure Operation | 500.4 II |
| High Temperature Storage | 501.4 I |
| High Temperature Operation | 501.4 II |
| Low Temperature Storage | 502.4-3 I |
| Low Temperature Operation | 502.4-3 II |
| Temperature Shock | 503.4 I |
| Solar Radiation | 505.4 I |
| Rain Blowing | 506.4 I |
| Rain Drip | 506.4 III |
| Humidity Induced | 507.4 |
| Salt Fog | 509.4 |
| Dust Blowing | 510.4 I |
| Vibration | 514.5 I |
| Shock Functional | 516.5 I |
| Shock Transit Drop | 516.5 IV |
All stated specifications are subject to change without notice or obligation.